System Information FLORA 370 TS2

最初にディスプレイキーボードマウス等装着して電源をいれると。

起動その１

このような形で起動します。まあ手で写したので写し間違いが多々有ると思いますが、このような物です。


              HITACHI
             -----------

   Enter Setup, Press Ctrl_Alt_Esc key

暫くして

PXE-M00: Initializing LANDesk (R) Service Agent.
PXE-M04: Hooking bootstrap interrupt 18h.

Adaptec AHA-2940 Ultra/Ultra W SCSI BIOS  v1.32
(c) 1997  Adaptec, Inc, All Rights Reserved.

<|<|<| Press < Ctrl><A> for SCSISlect (TM) Utility! |>|>|>


No SCSI boot Device Found

SCSI BIOS not installed!

通常はこの後正常に OS が起動すると云う事になります。今回はそうでは無くて、文字は青だったかもしれませんが

Unread Event(s) Found
Press Ctrl_Alt_Esc key to enter Setup or F1 key to continue...

このような状態で停止したようになります。”F1” を押せば起動はします。正常な起動と同じ様な感じなのです。しかしディスプレイ、キーボード及びマウスを接続しないで運用をしようとすると不都合です ”F1” を押せませんので、その件は置いておいて ”Ctrl_Alt_Esc key”してみます。

続いて雰囲気として、（上手く表示できないな）実際の画面とは異なりますし手で写したので間違いがありますがおおよそは

Setup Utility



                 Setup Utility                    


・System Information
・Product  Information
・Disk Drives
・Onboard Peripherals
・Power Management 
・Boot Options
・Date and Time
・System Security
・Advanced Options

Load Default Settings
Abort Settings Change

<↑><↓> Move hightlight bar              <←> Select /* きっと Enter キー でしょう */
<Esc> Exit

System Information

残りは青地白文字ということで実際のものとは異なります。

    System Information

Processor ----------------------------- Pentium II
Processor Speed ----------------------- 400MHz
Internal Cache -------------------------32KB,Enabled
External Cache ------------------------ 512KB,Enabled
Floppy Drive A ------------------------ 1.44MB 3.5-inch
Floppy Drive B ------------------------ None
IDE Primary Channel Master ------------ Hard Disk,76319 MB 
IDE Primary Channel Slave ------------- None
IDE Secondary Channel Master ---------- IDE CD-ROM
IDE Secondary Channel Slave ----------- None
Total Memory -------------------------- 192 MB
1st Bank ------------------------------ SDRAM,64 MB
2nd Bank ------------------------------ SDRAM,128 MB
3rd BAnk ------------------------------ None

<PgUp><PgDn> Move screen
<Esc> Back to Main Menu

ハードディスクはこれがついています。

hda: Hitachi HDS721680PLAT80, ATA DISK drive

まあそういうことです。またメモリは増設してあります。

めくると

    System Information

Serial Port 1 -------------------------- 3F8h, IRQ 4 \
/* ttyS00 at 0x03f8 (irq = 4) is a 16550A */
Serial Port 2 -------------------------- 2F8h, IRQ 3 \
/* ttyS01 at 0x02f8 (irq = 3) is a 16550A */
Parallel Port  ------------------------- 378h, IRQ 7
PS/2 Mouse  ---------------------------- Installed
Memory Parity Mode  -------------------- ECC
USB Host Controller  ------------------- Enabled


<PgUp><PgDn> Move screen
<Esc> Back to Main Menu

Product Information

    Product Information
Product Name  ------------------ FLORA 370 TS2
System S/N --------------------- N/A
Main Board ID ------------------ V66XA
Main Board  S/N ---------------- N/A
System BIOS Version ------------ V3.2
DMI  BIOS Version -------------- 2.00.1

<Esc> Back to Main Menu

Disk Drives

    Disk Drives
Floppy Drive A  ------------------ [1.44MB 3.5-inch]
Floppy Drive B  ------------------ [    None       ]
 

Super Disk drive as -------------- [    None       ]

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

Onboard Peripherals

    Onboard Peripherals
Serial Port 1 ---------------[Enabled]
  Base Address --------------[3F8h]
  IRQ  ----------------------[4]

Serial Port 2 ---------------[Enabled]
  Base Address --------------[2F8h]
  IRQ  ----------------------[3]

Parallel Port ---------------[Enabled]
  Base Address --------------[378h]
  IRQ  ----------------------[7]
  Operation Mode ------------[Bi-directional]
    ECP DMA Channel ---------[-]

・Onboard Device Settengs

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

めくると

    Onboard Device Settings
Floppy Disk Controller ------[Enabled]
IDE  Controller -------------[ Both ]
PS/2 Mouse  Controller ------[Enabled]
USB Host    Controller ------[Enabled]
   USB Legacy Mode  ---------[Disabled]
Onboard Audio Chip   --------[Enabled]

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

Power Management

    Power Management 

Power Management Mode ----------[Enabled]
  IDE Hard Disk Standby Timer --[OFF]
  System Sleep Timer -----------[OFF]
   Sleep Mode ------------------[--------]

Power Switch < 4 sec. ----------[ Suspend ]

Schedule Resume from Suspend ---[Disabled]
    Resume Time ----------------[--:--:--]

System wake-up event
   Modem Ring Indicator --------[Enabled]

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

Boot Options

    Boot Options 
Boot Sequence
  1st.  [Floppy Disk]
  2nd.  [Hard Disk]
  3rd.  [IDE CD-ROM]
  4th.  [LANDesk (R) Service Agent]

First Hard Disk Drive -----[IDE]
Primary Display Adapter ---[ Auto ]

Fast Boot  ----------------[Disabled]
Silent Boot  --------------[Enabled]
Num Lock After Boot -------[Enabled]
Memory Test ---------------[Disabled]

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

Date and Time

    Date and Time 
Date ----------------[Tue May 25,2010]
Time-----------------[01:23:45]

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

System Security

    System Security

Setup Password ---------------------[None]
Power-on Password ------------------[None]

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

Advanced Options

    Advanced Options
・Memory/Cache Options
・PnP/PCI Options
・System Event Configuration

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←> Select /* きっと Enter キー でしょう */

めくると

Memory/Cache Options

    Memory/Cache Options

Internal Cache (CPU Cache)  -------[Enabled]
External Cache   ------------------[Enabled]
  Cache Scheme ------------------- Write Back

Memory at 15MB-16MB Reserved for ---[ System ]
Memory Parity Mode -----------------[ ECC ]
UPS Mode ---------------------------[Pre-State]
C8000h - DFFFFh Shadow -------------[Disabled]

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

Esc で戻ってめくると

PnP/PCI Options

    PnP/PCI Options
PCI IRQ Setting     --------------[ Auto ]

                             INTA  INTB INTC  INTD
PCI Slot 1 ----------------  [10]  [11] [--]  [11]
PCI Slot 2 ----------------  [11]  [--] [11]  [10]
PCI Slot 3 ----------------  [--]  [11] [10]  [11]

PCI IRQ Sharing ----------------[Yes]
VGA Palette Snoop  -------------[Disabled]
Graphics Apertures Size --------[64 ] MB
Plug and Play OS ---------------[No]
Reset Resource Assingnments ----[No]

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

Esc で戻ってめくると

System Event Configuration

    System Event Configuration

System Event Logging
   Total Event Log Number ------------ 18
   Remain of Event Log Area ---------- 40%
   Event Logging ---------------------[Enabled]
   Clear Event Log -------------------[Disabled]


・  View Event Logs

<↑><↓> Move highlight bar   <F1> Help
<Esc> Exit                    <←><→> Change setting

これは有る時点でのデーターの写しです。

View Event Logs

    View Event Logs


No  Type                                Time                    Status


 1   Multi-bit ECC Memory Error          12:51 May 21, 2010      Viewed 
     DIMM  2,    1  time(s)

 2   Post Error ( ID: 72)                12:00 Jan 01, 1998      Viewed 
     CMOS Checksum Error

 3   Post Error ( ID: 71)                12:00 Jan 01, 1998      Viewed    
     CMOS Battery Bad

 4   Post Error ( ID: 61)                12:00 Jan 01, 1998      Viewed 
     CPU Clock Mismatch

 5   Post Error ( ID: 72)                12:00 Jan 01, 1998      Viewed 
     CMOS Checksum Error

 6   Post Error ( ID: 71)                12:00 Jan 01, 1998      Viewed    
     CMOS Battery Bad

 7   Post Error ( ID: 61)                12:00 Jan 01, 1998      Viewed 
     CPU Clock Mismatch

 8   Post Error ( ID: 51)                10:43 Jan 02, 1998      Viewed 
     IDE Primary Channel Slave Driver Error

 9   Post Error ( ID: 51)                10:22 Jan 02, 1998      Viewed 
     IDE Primary Channel Slave Driver Error

10   Post Error ( ID: 51)                10:09 Jan 02, 1998      Viewed 
     IDE Primary Channel Slave Driver Error

11   Post Error ( ID: 51)                10:16 Jan 01, 1998      Viewed 
     IDE Primary Channel Slave Driver Error

12   Post Error ( ID: 51)                10:09 Jan 01, 1998      Viewed 
     IDE Primary Channel Slave Driver Error

13   Post Error ( ID: 72)                12:03 Jan 01, 1998      Viewed 
     CMOS Checksum Error

14   Post Error ( ID: 51)                12:03 Jan 01, 1998      Viewed 
     IDE Primary Channel Slave Driver Error

15   Post Error ( ID: 51)                12:14 Jan 01, 1998      Viewed 
     IDE Primary Channel Slave Driver Error

16   Post Error ( ID: 72)                12:03 Jan 01, 1998      Viewed 
     CMOS Checksum Error

17   Post Error ( ID: 51)                12:03 Jan 01, 1998      Viewed 
     IDE Primary Channel Slave Driver Error

18   Log Area Reset/Cleared              18:46 Nov 06, 1998      Viewed 


<PgUp><PgDn> Move screen
<Esc> Back to Main Menu

写し間違い等多々有ると思いますがおおよそこのような物です。

にゃんたろう拝！

2010年 5月27日 (木) 21:01:09 JST 作成

戻る

System Information FLORA 370 TS2

起動 その１

Setup Utility

System Information

Product Information

Disk Drives

Onboard Peripherals

Power Management

Boot Options

Date and Time

System Security

Advanced Options

Memory/Cache Options

PnP/PCI Options

System Event Configuration

View Event Logs

起動その１